Grade 3 · Design & Engineering · Lesson 156

Foil Ferry

Build a wide foil ferry that floats while carrying four large plastic passengers.

Time2 × 45 minutesTeamsPairs; alternate builder and testerEquipmentBasic classroom design materials; no powered equipment

Your project in view

What you are making

Build a wide foil ferry that floats while carrying four large plastic passengers.

This generated example illustrates one possible finished design—not actual student work. Use the lesson’s sizes, connected parts and safety steps; your colors and creative details can be different.

Generated finished-project example for Foil Ferry: Build a wide foil ferry that floats while carrying four large plastic passengers.
Foil Ferry · Generated project example

Student directions · Grade 3

What will you make and do?

Build a wide foil ferry that floats while carrying four large plastic passengers.

Teacher overview: Students will plan the specific object described below, make and test a first version, then use their results to improve it. Read one step together, demonstrate the unfamiliar action, and let students complete that step before moving on.

  1. 1Plan your project

    Draw a narrow boat and a wide ferry. Mark raised edges and balanced passenger positions.

  2. 2Make the first parts

    Fold the foil into a flat-bottomed tray with sealed pinched corners and no holes.

  3. 3Put it together

    Float it empty, then add passengers one at a time in the planned positions.

  4. 4Test it fairly

    Carry all four for 20 seconds in three trials. Record water entry, tilt and passenger loss.

  5. 5Improve one part

    Use an equal foil square to change base width, edge height or passenger layout and repeat.

  6. 6Show and turn in

    Submit the finished foil ferry, two labeled ideas and before-and-after evidence. Explain which change the results support.

How will you know it works?

  • Floats without leaking
  • Carries all four passengers for 20 seconds
  • Record the stated test and explain one revision

Before you move on

Tell a partner what you are making. Point to the part you will work on next. Draw or dictate your test notes if writing slows you down.

Machine cutting, printer setup and electrical power-on require adult approval. A basic-materials model is a valid way to demonstrate the design when equipment is unavailable.

Keep your plan, test notes and before-and-after evidence with the printable design brief below. Use the detailed teacher plan and any coding guide for tool instructions. These steps continue across the lesson’s meetings, not all in one sitting.

For teachers

Engineering standards

This shows how the lesson connects to the national NGSS engineering standards and what student work you can collect.

Assessed

3-5-ETS1-1

Define the need in Build a wide foil ferry that floats while carrying four large plastic passengers. Agree on the two success checks and the listed material limits.

What students show: Two labeled ideas with the target and limits stated.
Practiced

3-5-ETS1-2

Compare the ideas using the project checks: Floats without leaking; Carries all four passengers for 20 seconds.

What students show: A selected design with a reason connected to a success check.
Assessed

3-5-ETS1-3

Test, change one feature and retest: Carry all four for 20 seconds in three trials. Record water entry, tilt and passenger loss. Use an equal foil square to change base width, edge height or passenger layout and repeat.

What students show: Before-and-after results collected under the same conditions.

Materials

  • Equal foil squares
  • shallow water tray
  • four large plastic animals or counters
  • towel
  • Pencil, planning paper and the printable design brief below

Teacher preparation

  1. Gather per-pair materials: Equal foil squares; shallow water tray; four large plastic animals or counters; towel.
  2. Make one rough sample and rehearse the exact test: Carry all four for 20 seconds in three trials. Record water entry, tilt and passenger loss.
  3. Set the size, load or distance marks mentioned in the steps before class. Demonstrate an ordinary first attempt, not a perfect model to copy.
  4. Prepare any holes, fasteners or difficult cuts for students. Check the stated safety note and clear the testing space.

Step by step

How to teach it

Meeting 1 · 0–8 min

See the job and plan

  1. Introduce the finished object: Build a wide foil ferry that floats while carrying four large plastic passengers.
  2. Draw a narrow boat and a wide ferry. Mark raised edges and balanced passenger positions.
  3. Students say what would count as a successful result.
Meeting 1 · 8–18 min

Model the unfamiliar action

  1. Demonstrate slowly: Fold the foil into a flat-bottomed tray with sealed pinched corners and no holes.
  2. Pause so partners can repeat the action; provide prepared parts if cutting or folding blocks progress.
Meeting 1 · 18–35 min

Build the first version

  1. Float it empty, then add passengers one at a time in the planned positions.
  2. Partners swap builder and checker roles halfway through. Check the working part before decorating.
Meeting 1 · 35–45 min

Try once and save

  1. Run one trial of the stated test to locate an obvious problem. Do not count a changed procedure as a fair comparison.
  2. Label and store the model; sketch its current shape and clear the work area.
Meeting 2 · 0–8 min

Predict and set up

  1. Revisit the two success checks. Agree on identical starting conditions and prepare a before/after results table.
Meeting 2 · 8–23 min

Collect evidence

  1. Carry all four for 20 seconds in three trials. Record water entry, tilt and passenger loss.
  2. One student operates while the other records. Swap for a later trial while noting a change of operator if it affects the result.
Meeting 2 · 23–35 min

Change one thing

  1. Use an equal foil square to change base width, edge height or passenger layout and repeat.
  2. Keep the original results rather than replacing them with only the best attempt.
Meeting 2 · 35–45 min

Explain and clean up

  1. Submit the finished foil ferry, two labeled ideas and before-and-after evidence. Explain which change the results support.
  2. Collect the brief and results; separate reusable materials and clean the test area.

Assessment

  • Floats without leaking
  • Carries all four passengers for 20 seconds
  • Student demonstrates the actual task: Carry all four for 20 seconds in three trials. Record water entry, tilt and passenger loss.
  • Record includes failures as well as successes.
  • Student identifies one changed feature and uses the retest to explain the result.

Supports & extensions

  • Provide fold marks or pre-cut parts; accept drawings or dictated observations.
  • Start with the smallest working version of foil ferry before decoration.
  • Extension after success: choose one more value for the same tested feature, predict its effect and repeat carry all four for 20 seconds in three trials.

Safety & responsible use

  • Teacher checks materials and test conditions before use. Use classroom scissors; adults prepare difficult cuts, holes and fasteners.
  • No powered tools, coding, hot glue or electrical circuits are required. Keep moving objects contained and test loads light.
  • Use shallow trays away from electronics. Wipe spills immediately and do not drink test water.

No-machine alternative

Use prepared paper parts, larger pieces or an adult-assisted version of the same build. Keep the functional task: Build a wide foil ferry that floats while carrying four large plastic passengers. If physical testing is not possible, label sketches as predictions rather than measured results.

Printable student design brief

The challenge

Build a wide foil ferry that floats while carrying four large plastic passengers.

Success criteria

  • Floats without leaking
  • Carries all four passengers for 20 seconds
  • Record the stated test and explain one revision

Constraints

  • Use only the listed teacher-approved materials
  • Stay within the teacher-set size, load and test-space limits
  • Two 45-minute meetings; keep the first version simple

Engineer’s notes

Who uses this object, and what should it do?
Draw two possible designs. Label the working parts and circle your choice.
Which size, fold, gap or position must you measure or mark?
Before testing, predict what will happen: Carry all four for 20 seconds in three trials. Record water entry, tilt and passenger loss.
Record each trial: condition / expected result / actual result.
Draw the ONE change you made. What stayed the same?
Record the retest. Did the change help, not help, or leave the result uncertain?
Show and explain: one result that supports your conclusion.
← Return to lesson library