Grade 3 · Low-Tech Builds · Lesson 85

Secret Picture Slider

Make a paper sleeve with a window that reveals one of two pictures when a tab slides.

Time2 × 45 minutesTeamsPairs; alternate builder and testerEquipmentBasic classroom materials; no powered equipment

Your project in view

What you are making

Make a paper sleeve with a window that reveals one of two pictures when a tab slides.

This generated example illustrates one possible finished design—not actual student work. Use the lesson’s sizes, connected parts and safety steps; your colors and creative details can be different.

Generated finished-project example for Secret Picture Slider: Make a paper sleeve with a window that reveals one of two pictures when a tab slides.
Secret Picture Slider · Generated project example

Student directions · Grade 3

What will you make and do?

Make a paper sleeve with a window that reveals one of two pictures when a tab slides.

Teacher overview: Students will plan the specific object described below, make and test a first version, then use their results to improve it. Read one step together, demonstrate the unfamiliar action, and let students complete that step before moving on.

  1. 1Plan your project

    Sketch two pictures and the window that will reveal them. Mark how far the strip must move.

  2. 2Make the first parts

    Fold a sleeve around a long paper strip, leaving enough space for easy sliding.

  3. 3Put it together

    Cut the window with teacher help and place the two pictures on the strip at the tested positions. Add stop tabs.

  4. 4Test it fairly

    Slide between the two pictures five times. Record jams and whether each picture is fully visible.

  5. 5Improve one part

    Change one sleeve gap or picture position. Repeat all five cycles.

  6. 6Show and turn in

    Show the two states and submit a window-and-strip plan with test notes.

How will you know it works?

  • Reveals two clear pictures
  • Stop tabs keep the strip from falling out
  • Record the stated test and explain one revision

Before you move on

Tell a partner what you are making. Point to the part you will work on next. Draw or dictate your test notes if writing slows you down.

Machine cutting, printer setup and electrical power-on require adult approval. A basic-materials model is a valid way to demonstrate the design when equipment is unavailable.

Keep your plan, test notes and before-and-after evidence with the printable design brief below. Use the detailed teacher plan and any coding guide for tool instructions. These steps continue across the lesson’s meetings, not all in one sitting.

For teachers

Engineering standards

This shows how the lesson connects to the national NGSS engineering standards and what student work you can collect.

Assessed

3-5-ETS1-1

Define the need in Make a paper sleeve with a window that reveals one of two pictures when a tab slides. Agree on the two success checks and the listed material limits.

What students show: Two labeled ideas with the target and limits stated.
Practiced

3-5-ETS1-2

Compare the ideas using the project checks: Reveals two clear pictures; Stop tabs keep the strip from falling out.

What students show: A selected design with a reason connected to a success check.
Assessed

3-5-ETS1-3

Test, change one feature and retest: Slide between the two pictures five times. Record jams and whether each picture is fully visible. Change one sleeve gap or picture position. Repeat all five cycles.

What students show: Before-and-after results collected under the same conditions.

Materials

  • Cardstock
  • paper strip
  • markers
  • scissors
  • tape
  • Pencil, planning paper and the printable design brief below

Teacher preparation

  1. Gather per-pair materials: Cardstock; paper strip; markers; scissors; tape.
  2. Make one rough sample and rehearse the exact test: Slide between the two pictures five times. Record jams and whether each picture is fully visible.
  3. Set the size, load or distance marks mentioned in the steps before class. Demonstrate an ordinary first attempt, not a perfect model to copy.
  4. Prepare any holes, fasteners or difficult cuts for students. Check the stated safety note and clear the testing space.

Step by step

How to teach it

Meeting 1 · 0–8 min

See the job and plan

  1. Introduce the finished object: Make a paper sleeve with a window that reveals one of two pictures when a tab slides.
  2. Sketch two pictures and the window that will reveal them. Mark how far the strip must move.
  3. Students say what would count as a successful result.
Meeting 1 · 8–18 min

Model the unfamiliar action

  1. Demonstrate slowly: Fold a sleeve around a long paper strip, leaving enough space for easy sliding.
  2. Pause so partners can repeat the action; provide prepared parts if cutting or folding blocks progress.
Meeting 1 · 18–35 min

Build the first version

  1. Cut the window with teacher help and place the two pictures on the strip at the tested positions. Add stop tabs.
  2. Partners swap builder and checker roles halfway through. Check the working part before decorating.
Meeting 1 · 35–45 min

Try once and save

  1. Run one trial of the stated test to locate an obvious problem. Do not count a changed procedure as a fair comparison.
  2. Label and store the model; sketch its current shape and clear the work area.
Meeting 2 · 0–8 min

Predict and set up

  1. Revisit the two success checks. Agree on identical starting conditions and prepare a before/after results table.
Meeting 2 · 8–23 min

Collect evidence

  1. Slide between the two pictures five times. Record jams and whether each picture is fully visible.
  2. One student operates while the other records. Swap for a later trial while noting a change of operator if it affects the result.
Meeting 2 · 23–35 min

Change one thing

  1. Change one sleeve gap or picture position. Repeat all five cycles.
  2. Keep the original results rather than replacing them with only the best attempt.
Meeting 2 · 35–45 min

Explain and clean up

  1. Show the two states and submit a window-and-strip plan with test notes.
  2. Collect the brief and results; separate reusable materials and clean the test area.

Assessment

  • Reveals two clear pictures
  • Stop tabs keep the strip from falling out
  • Student demonstrates the actual task: Slide between the two pictures five times. Record jams and whether each picture is fully visible.
  • Record includes failures as well as successes.
  • Student identifies one changed feature and uses the retest to explain the result.

Supports & extensions

  • Provide fold marks or pre-cut parts; accept drawings or dictated observations.
  • Start with the smallest working version of secret picture slider before decoration.
  • Extension after success: choose one more value for the same tested feature, predict its effect and repeat slide between the two pictures five times.

Safety & responsible use

  • Teacher checks materials and test conditions before use. Use classroom scissors; adults prepare difficult cuts, holes and fasteners.
  • No powered tools, coding, hot glue or electrical circuits are required. Keep moving objects contained and test loads light.
  • Keep pieces on the tabletop, do not mouth materials and stop if a part tears into a sharp or loose hazard.

No-machine alternative

Use prepared paper parts, larger pieces or an adult-assisted version of the same build. Keep the functional task: Make a paper sleeve with a window that reveals one of two pictures when a tab slides. If physical testing is not possible, label sketches as predictions rather than measured results.

Printable student design brief

The challenge

Make a paper sleeve with a window that reveals one of two pictures when a tab slides.

Success criteria

  • Reveals two clear pictures
  • Stop tabs keep the strip from falling out
  • Record the stated test and explain one revision

Constraints

  • Use only the listed teacher-approved materials
  • Stay within the teacher-set size, load and test-space limits
  • Two 45-minute meetings; keep the first version simple

Engineer’s notes

Who uses this object, and what should it do?
Draw two possible designs. Label the working parts and circle your choice.
Which size, fold, gap or position must you measure or mark?
Before testing, predict what will happen: Slide between the two pictures five times. Record jams and whether each picture is fully visible.
Record each trial: condition / expected result / actual result.
Draw the ONE change you made. What stayed the same?
Record the retest. Did the change help, not help, or leave the result uncertain?
Show and explain: one result that supports your conclusion.
← Return to lesson library