Grade 5 · Design & Engineering · Lesson 140

Dry Animal Shelter

Build a model shelter that keeps a toy animal dry during a gentle spray-bottle rain test.

Time2 × 45 minutesTeamsPairs; alternate builder and testerEquipmentBasic classroom design materials; no powered equipment

Your project in view

What you are making

Build a model shelter that keeps a toy animal dry during a gentle spray-bottle rain test.

This generated example illustrates one possible finished design—not actual student work. Use the lesson’s sizes, connected parts and safety steps; your colors and creative details can be different.

Generated finished-project example for Dry Animal Shelter: Build a model shelter that keeps a toy animal dry during a gentle spray-bottle rain test.
Dry Animal Shelter · Generated project example

Student directions · Grade 5

What will you make and do?

Build a model shelter that keeps a toy animal dry during a gentle spray-bottle rain test.

Teacher overview: Students will plan the specific object described below, make and test a first version, then use their results to improve it. Read one step together, demonstrate the unfamiliar action, and let students complete that step before moving on.

  1. 1Plan your project

    Measure the toy. Draw a flat roof and a sloped roof; mark openings and where water should travel.

  2. 2Make the first parts

    Build a stable frame and floor in the tray. Add a roof with an overhang larger than the toy.

  3. 3Put it together

    Cover or layer the roof using limited waterproof material. Keep the doorway usable.

  4. 4Test it fairly

    Place dry paper towel under the toy. Teacher sprays the same number of times from the same mark; check wet area in three trials.

  5. 5Improve one part

    Change one seam, roof angle or overhang. Replace the towel and repeat the same rain test.

  6. 6Show and turn in

    Turn in the shelter, cross-section drawing and wet-area comparison. Explain where water traveled.

How will you know it works?

  • Toy fits inside and can enter through the opening
  • Paper beneath the toy stays mostly dry during the test
  • Record the stated test and explain one revision

Before you move on

Explain which measurement, input or design choice you are testing. Predict the result and record what stays the same so your comparison is fair.

Machine cutting, printer setup and electrical power-on require adult approval. A basic-materials model is a valid way to demonstrate the design when equipment is unavailable.

Keep your plan, test notes and before-and-after evidence with the printable design brief below. Use the detailed teacher plan and any coding guide for tool instructions. These steps continue across the lesson’s meetings, not all in one sitting.

For teachers

Engineering standards

This shows how the lesson connects to the national NGSS engineering standards and what student work you can collect.

Assessed

3-5-ETS1-1

Define the need in Build a model shelter that keeps a toy animal dry during a gentle spray-bottle rain test. Agree on the two success checks and the listed material limits.

What students show: Two labeled ideas with the target and limits stated.
Practiced

3-5-ETS1-2

Compare the ideas using the project checks: Toy fits inside and can enter through the opening; Paper beneath the toy stays mostly dry during the test.

What students show: A selected design with a reason connected to a success check.
Assessed

3-5-ETS1-3

Test, change one feature and retest: Place dry paper towel under the toy. Teacher sprays the same number of times from the same mark; check wet area in three trials. Change one seam, roof angle or overhang. Replace the towel and repeat the same rain test.

What students show: Before-and-after results collected under the same conditions.

Materials

  • Cardboard
  • foil
  • craft sticks
  • tape
  • toy animal
  • spray bottle
  • tray
  • paper towel
  • Pencil, planning paper and the printable design brief below

Teacher preparation

  1. Gather per-pair materials: Cardboard; foil; craft sticks; tape; toy animal; spray bottle; tray; paper towel.
  2. Make one rough sample and rehearse the exact test: Place dry paper towel under the toy. Teacher sprays the same number of times from the same mark; check wet area in three trials.
  3. Set the size, load or distance marks mentioned in the steps before class. Demonstrate an ordinary first attempt, not a perfect model to copy.
  4. Prepare any holes, fasteners or difficult cuts for students. Check the stated safety note and clear the testing space.

Step by step

How to teach it

Meeting 1 · 0–8 min

See the job and plan

  1. Introduce the finished object: Build a model shelter that keeps a toy animal dry during a gentle spray-bottle rain test.
  2. Measure the toy. Draw a flat roof and a sloped roof; mark openings and where water should travel.
  3. Students say what would count as a successful result.
Meeting 1 · 8–18 min

Model the unfamiliar action

  1. Demonstrate slowly: Build a stable frame and floor in the tray. Add a roof with an overhang larger than the toy.
  2. Pause so partners can repeat the action; provide prepared parts if cutting or folding blocks progress.
Meeting 1 · 18–35 min

Build the first version

  1. Cover or layer the roof using limited waterproof material. Keep the doorway usable.
  2. Partners swap builder and checker roles halfway through. Check the working part before decorating.
Meeting 1 · 35–45 min

Try once and save

  1. Run one trial of the stated test to locate an obvious problem. Do not count a changed procedure as a fair comparison.
  2. Label and store the model; sketch its current shape and clear the work area.
Meeting 2 · 0–8 min

Predict and set up

  1. Revisit the two success checks. Agree on identical starting conditions and prepare a before/after results table.
Meeting 2 · 8–23 min

Collect evidence

  1. Place dry paper towel under the toy. Teacher sprays the same number of times from the same mark; check wet area in three trials.
  2. One student operates while the other records. Swap for a later trial while noting a change of operator if it affects the result.
Meeting 2 · 23–35 min

Change one thing

  1. Change one seam, roof angle or overhang. Replace the towel and repeat the same rain test.
  2. Keep the original results rather than replacing them with only the best attempt.
Meeting 2 · 35–45 min

Explain and clean up

  1. Turn in the shelter, cross-section drawing and wet-area comparison. Explain where water traveled.
  2. Collect the brief and results; separate reusable materials and clean the test area.

Assessment

  • Toy fits inside and can enter through the opening
  • Paper beneath the toy stays mostly dry during the test
  • Student demonstrates the actual task: Place dry paper towel under the toy. Teacher sprays the same number of times from the same mark; check wet area in three trials.
  • Record includes failures as well as successes.
  • Student identifies one changed feature and uses the retest to explain the result.

Supports & extensions

  • Provide a worked first joint or sample; have students record dimensions and explain one comparison limitation.
  • Start with the smallest working version of dry animal shelter before decoration.
  • Extension after success: choose one more value for the same tested feature, predict its effect and repeat place dry paper towel under the toy.

Safety & responsible use

  • Teacher checks materials and test conditions before use. Use classroom scissors; adults prepare difficult cuts, holes and fasteners.
  • No powered tools, coding, hot glue or electrical circuits are required. Keep moving objects contained and test loads light.
  • Teacher controls the spray bottle. Test only in a waterproof tray away from electronics and wipe spills immediately.

No-machine alternative

Use prepared paper parts, larger pieces or an adult-assisted version of the same build. Keep the functional task: Build a model shelter that keeps a toy animal dry during a gentle spray-bottle rain test. If physical testing is not possible, label sketches as predictions rather than measured results.

Printable student design brief

The challenge

Build a model shelter that keeps a toy animal dry during a gentle spray-bottle rain test.

Success criteria

  • Toy fits inside and can enter through the opening
  • Paper beneath the toy stays mostly dry during the test
  • Record the stated test and explain one revision

Constraints

  • Use only the listed teacher-approved materials
  • Stay within the teacher-set size, load and test-space limits
  • Two 45-minute meetings; keep the first version simple

Engineer’s notes

Who uses this object, and what should it do?
Draw two possible designs. Label the working parts and circle your choice.
Which size, fold, gap or position must you measure or mark?
Before testing, predict what will happen: Place dry paper towel under the toy. Teacher sprays the same number of times from the same mark; check wet area in three trials.
Record each trial: condition / expected result / actual result.
Draw the ONE change you made. What stayed the same?
Record the retest. Did the change help, not help, or leave the result uncertain?
Show and explain: one result that supports your conclusion.
← Return to lesson library